AutoGG_0_2_9b 2017-02-07

The AutogGG is a program that helps you to:

- Read the Nand of the Xbox. Autodetect the model.
- Generate Nand to load Xell in console to obtain Cpukey.
- Once you have CpuKey.Generate Jtag / rgh (Glitch) / Retail, images
- Flash generated Nand through programmer (LPT/USB) or software (Xell or Dash)

But AutoGG also allows many more options (Addons)
- Change temperature sensors on the console.
- Change data in the console: Serial, Reader Type (Osig), Region and dvdkey.
- Map / unmap Bad Blocks.
- Inject / Extract specific data from the console. to repair corrupt nands
- Decrypt X-Val to check marks on console by Microsoft.
- UnCripple to try to clear the console marks,
- Make only a partial reading of only 1Mb of Nand then read the rest through Xell and finally merge to get the full Nand much faster (Recommended for slow nands readers LPT)
...


INSTRUCTIONS

Note:First you must know that to manage Nand of console have RISK OF BRICK
DO IT UNDER YOU RESPONSABILITY .
This program is only a GUI to make (read / Build / write) of the image of your console released by the XEBUILD dev team and Tiros (nandpro). All credits and merits are for them.
I am totally against the use of any method that violates copyright. This program is only developed to give the user the possibility to run free software, and ,in any case, the use of illegal software



1. The program needs a dump (read) from nand console. We can get it in 3 ways :
Reading nand using a Nand reader . If we have Nand Flasher you only have to choose the port (LPT / USB) and click on Read Nand. The autoGG will try to detect the size of the Nand (if not detected select manually) then we ask how many read you want to make of your nand (2 recommended) and Size you want to read (by default we mark the full nand size) and then will proceed to make them ,compared to ensure they are correct. If no errors make a copy in the desired path

If your console already has made the exploit you can get the dump through Net. Plug your local network (wireless or cable) and start the Xell. You will get IP on screen .Edit IP in autogg and click IP_Nand to read it.Save a copy. Click CPUKEY to decrypt .If everything is correct you will be prompted to save a copy of your encrypted data.

If you have an LPT Nand reader, readings will be very slow (up to 6 hours). There is a method to shorten this time dramatically. Search in this tutorial below (Tutorial to read Nand by Net after a first read of only 2 Mb USB / LPT) [*]If you had already saved the dump select it manually.[*]If nand has badblocks do not worry. Autogg auto map them automatically

2. To generate Images autogg need cpukey of the console. If you have not it you will have to get it generating NandXell . To do this click Generate Xell, and once generated Flash Xell. This will allow you to load Xell and will display the Cpukey necessary for the rest of the process. Once the console boot Xell you can copy CPUKEY by hand from the screen or if you have connected console to the network, you can put IP console (shown in Xell screen) in autogg and press CpuKey. Once you have introduced cpukey program automatically generate a file with the model name, serial number and cpukey to make a backup with all data.

3. With the correct cpukey we can generate / Flash Glitch JTAG or Retail images.. In the case of Jtags you must select the Xell modelo and SMC you want to inject.
In Jasper models Big Blocks (256/512) theres is NandMu option to disable NAND memory unit. In Slim you have the option nofcrt to disable the file FCRT.bin..

There are more optional Addons.

Map/Unmap Bad blocks yf necesary.

Change Temperatures

Extract/Inyect/Repair Nand expecific Data.

Edit CF-LDV

UnCripple

4.Once you have booted into the new Dash you could need to update (avatar. ..) .

Download Oficial Dash USB Update from Microsoft Web.

Copy into a USB and inserted it into the console in the original dash. (Not in the FSD)
If it dont update rename the folder $ystemupdate to $$ystemupdate and retry

If your console is banned now you can play online through the Xlink without Ping Limit.

NOTE:

Sometimes you Flash with a selected nandpro version and it seems to be all right. But the console has problems, do not start or fails .Then you try capacitors, cable lengths but sometimes you only need to select another Nandpro version in autoGG.


UPDATE DASH ON EXPLOITED CONSOLES WITHOUT OPEN CONSOLE OR USE ANY HARD:




ATTENTION. This method is dangerous if you fail your console may not boot. .

For those who already have done Exploit can update it without Hardware.

-Turn on the console on Xell. IP of the console Will be show .
-Edit IP console in AutoGG .Click on IP-Nand and wait download. Once finished save it. . Then click on CPUKEY to decrypt all data of your console. Save file with your data.

For rest of the generation process go point 3 of the tutorial.

Tutorial to read full Nand by Net reading only 1 Mega by USB/LPT::



If you have a slow nand reader, the reading process can take hours.
There is the possibility of read-only area we need to generate the NandXell and once loaded in console then to read the rest of the Nand by Network

The process is as follows:

1-Press Read nand. Choose Size 1Meg. Save file.
2-Choose image type (Glitch / JTAG) and click Generate NandXell.Once generated write it clicking Flash Xell. If all is ok start the console with network cable connected and chip installed. you will get the screen Xell
3-When Xell start IP will be assigned to the console and show us on screen. Write it in the IP field of autoGG and press IP-Nand to read and save file.
4-Press Inject 1M and choose the file saved in the first point. Save file.

Now you have the original nand .

CHANGE TEMPERATURES



In Nand are the parameters to regulate the temperature of CPU, GPU and Ram. The first 3 parameters are the objective temperatures by regulating the speed of the fans. The latter three parameters are the limit temperatures. If limit is exceeded the console shut down for protection.
To change these parameters only have to edit and click Change Temp button.
These will be stored and when we generate the image (Retail / Jtag / Glitch) shall apply the new parameters.
We must be careful with these option because if we set too much temperatures can burn the console . If we put too low fans will always be very fast and noise.

REPAIR NAND INYECTING DATA FROM DONOR NAND



This process needs CPUKEY FROM y our nand. If we have not it you can generate a nand Xell from donor with the same version of CB and obtain the CPUKEY.
If your Nand is corrupted or has a problem you can try to solve it injecting your data to a donor Nand with the same version of CB.
Load your dump and go to the section of Inject / Repair.
Press extract. The program will extract all valid specific data from nand and save them to destination folder.
Successfully extracted will be marked green and corrupt.ones with red
The Keyvault is needed.
Now load donor and click Inyect. The program will ask for the folder with the extracted data and will try to inject them into the donor nand . Autogg then generate a retail and save it to destination.
If theres no errors you have your New Nand..

DECRYPT X-VAL



If we want to see if YOUR console is marked you only have to turn on your console and go system configuration menu,console information see the number of serial and the X value of the console. Copy to autoGG in Section X-val and Press the button.Status of your console will be shown (Rev-25, Banned ...)

MODIFY YOUR CONSOLE DATA:



You have the option to modify the console data: Num.Serie, type reader (Osig), Region and dvdkey.

Just load your nand and modify data. Click on Patch and new Nand will be created and a copy will be saved. Now you can load and flash it or directly click on Raw-Flash USB to write through Xell.

Unmarked / UnBANN



If we have the console marked (ap-25 failed ...) you can try to unmark it in 2 ways.
1.-With nand reader click on unCripple. Does not always work
2.-Do all the process ;reading of Nand, obtaining CpuKey through Xell and generate / Flash a new image.

If the console is already banned your only option would be to inject an unbanned keyvault from a donor nand. But this is only for offline because donor keyvault only works with exploit and these can not connect to Live.

NOTE:

I will clarify everything about banned consoles according to my knowledge:

The first thing that happens in the process of banning is that the console is marked
At this stage you may not notice anything or ap-25 titles may stop working .
It is in the Ban Day when our console is banned and when you notice it.
What microsoft use to detect your banned console is in the Keyvault .

So we can inject to a banned console the keyvault of an unbanned console. But there is a problem.
The console has a keyvault Hash Check .
If we have the chip in the console kernel will be patched to bypass this protection and will run fine, but only offline ,we can not enter Live with exploited console. Then we might think we could unban with donated keyvault, create retail image and then remove the chip to go back to Live.
But as I said without the exploit does not bypass the protection of Keyvault hash and will show boot error.

MODIFY YOUR CONSOLE DATA:

You have the option to modify the console data: Num.Serie, type reader (Osig), Region and dvdkey.

Just load your nand and modify data. Click on Patch and Keyvault will be pached. Now you must create an image rgh / jtag and chip / jtag installed. Finally flash it or click on Raw-Flash to write with Xell.

Thanks to:

GLIGLI (Glitch)
Tiros (NandPro)
GG/FB team: Xebuild
boby2pc : Findsecdata
cOz~ashLaunch
BestPig:FcrtExtractor
EOL users for test and support.

Everyone involved...